Guide · fault codes

Fault codes that matter for tuning.

61 OBD codes we see in the workshop: what they mean, the usual causes, and whether the car is ready for a tune.

P0299

Check before tuning

Turbocharger underboost

Boost pressure stays below the target the ECU asks for.

Usual causes
Boost leak (split intercooler hose, loose clamp), sticking VGT vanes, faulty boost control valve (N75) or actuator, blocked DPF or catalyst, or a file asking for more boost than the turbo can make.
In the workshop
Repair first. Tuning a car with an active P0299 makes it worse. Smoke-test the intake and check actual vs. requested boost in live data.
P0299: full page →

P0234

Check before tuning

Turbocharger overboost condition

Boost pressure rises above the allowed maximum.

Usual causes
VGT vanes or wastegate stuck closed, faulty boost pressure sensor, damaged vacuum lines, or a file with boost targets above the limiter.
In the workshop
Check the actuator and sensor. If it appears right after a tune, the file needs correcting, not the car.
P0234: full page →

P0045

Check before tuning

Turbocharger boost control "A" circuit / open

The ECU sees an electrical fault in the boost control valve or actuator circuit.

Usual causes
Broken wire, corroded connector, failed boost control solenoid or electronic VGT actuator.
In the workshop
Electrical repair. Check resistance of the solenoid and the wiring before any tune.
P0045: full page →

P0046

Check before tuning

Turbocharger boost control "A" circuit range/performance

The boost control circuit works but does not move the turbo as expected.

Usual causes
Sticking VGT linkage, weak actuator, vacuum leak to the actuator, faulty position sensor.
In the workshop
Run an actuator test with the diagnostic tool. A sticky VGT must be freed or replaced before tuning.
P0046: full page →

P0236

Check before tuning

Boost pressure sensor "A" circuit range/performance

The boost sensor reading does not make sense compared to other values.

Usual causes
Oily or failed MAP sensor, leak in the sensor hose, wrong sensor fitted.
In the workshop
Compare boost and atmospheric pressure with the engine off. They should read almost the same.
P0236: full page →

P2263

Check before tuning

Turbocharger boost system performance

The ECU sees that the boost system as a whole does not perform as expected.

Usual causes
Boost leak, worn turbo, sticking VGT, exhaust restriction (DPF, catalyst), faulty sensor.
In the workshop
Treat like P0299: find the leak or restriction before a tune.
P2263: full page →

P0100

Check before tuning

Mass air flow circuit

Electrical fault in the mass air flow sensor circuit.

Usual causes
Failed MAF sensor, broken wire, bad connector, missing power supply.
In the workshop
Replace or repair before tuning. The ECU runs on substitute values with this code.
P0100: full page →

P0101

Check before tuning

Mass air flow sensor range/performance

The MAF reading does not match the air mass the ECU expects.

Usual causes
Dirty or ageing MAF, intake leak after the sensor, open intake fitted without recalibration.
In the workshop
Fix the sensor or intake. A Stage 2 intake needs a file made for it.
P0101: full page →

P0102

Check before tuning

Mass air flow circuit low

The MAF signal is below its normal electrical range.

Usual causes
Failed sensor, open circuit, poor ground, blocked air filter in extreme cases.
In the workshop
Electrical repair first.
P0102: full page →

P0103

Check before tuning

Mass air flow circuit high

The MAF signal is above its normal electrical range.

Usual causes
Failed sensor, short in the signal wire, wrong sensor fitted.
In the workshop
Electrical repair first.
P0103: full page →

P2279

Check before tuning

Intake air system leak

Measured air does not match what the engine is drawing.

Usual causes
Split intercooler hose, cracked intake pipe, leaking PCV or oil separator.
In the workshop
Smoke-test the intake before any tune.
P2279: full page →

P0171

Check before tuning

System too lean (bank 1)

The petrol engine runs leaner than the ECU can correct.

Usual causes
Vacuum leak, dirty MAF, weak fuel pump, clogged injectors, leaking PCV.
In the workshop
Never tune a lean engine. Find the leak or fuel supply problem first.
P0171: full page →

P0172

Check before tuning

System too rich (bank 1)

The petrol engine runs richer than the ECU can correct.

Usual causes
Leaking injector, high fuel pressure, faulty MAF or lambda sensor, wrong calibration after a modification.
In the workshop
Check injectors and fuel pressure. If it starts after a tune, the fuel model in the file needs correcting.
P0172: full page →

P0087

Check before tuning

Fuel rail / system pressure too low

Rail pressure stays below target.

Usual causes
Weak lift pump, blocked fuel filter, worn high-pressure pump, leaking injector return, air in the fuel.
In the workshop
Always check fuel supply before raising injection in a file.
P0087: full page →

P0088

Check before tuning

Fuel rail / system pressure too high

Rail pressure goes above the allowed maximum.

Usual causes
Faulty pressure regulator or rail pressure sensor, or rail pressure raised past the hardware limit in a file.
In the workshop
A tune must stay inside the rail pressure limit of the pump and injectors.
P0088: full page →

P0263

Check before tuning

Cylinder 1 contribution/balance

Cylinder 1 delivers more or less power than the others (diesel injector balance).

Usual causes
Worn or sticking injector, low compression, injector coding wrong after replacement.
In the workshop
Check injector correction values. Injectors with large corrections should be tested before a tune.
P0263: full page →

P0300

Check before tuning

Random / multiple cylinder misfire

Misfires detected on more than one cylinder.

Usual causes
Worn plugs or coils, injector fault, vacuum leak, low fuel pressure, ignition timing too aggressive.
In the workshop
Fix ignition and fuel before tuning. Petrol Stage 2 needs fresh plugs, often one step colder.
P0300: full page →

P0325

Check before tuning

Knock sensor 1 circuit (bank 1)

Electrical fault in the knock sensor circuit.

Usual causes
Failed sensor, loose mounting torque, damaged wire.
In the workshop
The ECU retards timing with this code. Repair before a petrol tune.
P0325: full page →

P0380

Check before tuning

Glow plug / heater circuit "A"

Fault in the diesel glow plug circuit or control module.

Usual causes
Burnt glow plug, failed glow plug relay or module, wiring fault.
In the workshop
Measure each plug. Does not block a tune but causes hard starts and smoke.
P0380: full page →

P0500

Check before tuning

Vehicle speed sensor "A"

Missing or implausible vehicle speed signal.

Usual causes
Wheel speed sensor fault, ABS module fault, gearbox output speed sensor.
In the workshop
Repair. Speed-based limiters and torque maps depend on this signal.
P0500: full page →

P0562

ECU / write fault

System voltage low

The ECU sees supply voltage below its normal range.

Usual causes
Weak battery, failing alternator, bad ground, voltage drop while cranking or reading the ECU.
In the workshop
Important for reading and writing: always use a stable charger. Low voltage is the most common cause of a failed write.
P0562: full page →

P0400

Software solution

EGR flow

The ECU sees an EGR flow problem.

Usual causes
Carbon-blocked EGR valve or cooler, faulty actuator or position sensor.
In the workshop
Clean or replace the valve. Software solution available on request.
P0400: full page →

P0401

Software solution

EGR flow insufficient

The EGR valve does not deliver the expected flow.

Usual causes
Carbon-blocked EGR valve or cooler, faulty actuator.
In the workshop
Clean or replace the valve. Software solution available on request.
P0401: full page →

P0402

Software solution

EGR flow excessive

More exhaust gas is recirculated than requested.

Usual causes
EGR valve stuck open, faulty position sensor, carbon under the valve seat.
In the workshop
A valve stuck open causes smoke and low power. Repair or software solution on request.
P0402: full page →

P0403

Software solution

EGR control circuit

Electrical fault in the EGR valve control circuit.

Usual causes
Failed EGR motor or solenoid, broken wire, bad connector.
In the workshop
Electrical repair, or software solution on request.
P0403: full page →

P2008

Software solution

Intake manifold runner control circuit / open (bank 1)

Electrical fault in the swirl flap / runner control circuit.

Usual causes
Failed swirl flap actuator, broken wire, vacuum solenoid fault.
In the workshop
Swirl flaps can break and enter the engine. Repair or software solution on request.
P2008: full page →

P2002

Software solution

Diesel particulate filter efficiency below threshold (bank 1)

The particulate filter is not trapping soot as expected.

Usual causes
Cracked or damaged DPF, faulty differential pressure sensor, leaking sensor pipes.
In the workshop
Check the pressure sensor and pipes first. Software solution available on request.
P2002: full page →

P2452

Software solution

DPF differential pressure sensor "A" circuit

Electrical fault in the DPF pressure sensor circuit.

Usual causes
Failed sensor, damaged wiring, melted connector near the exhaust.
In the workshop
Replace the sensor. Without it the ECU cannot judge soot load.
P2452: full page →

P2453

Software solution

DPF differential pressure sensor "A" range/performance

The DPF pressure reading does not fit the operating condition.

Usual causes
Blocked or split sensor hoses, failed sensor, very full DPF.
In the workshop
Check the hoses (often cracked or swapped). Software solution available on request.
P2453: full page →

P2458

Software solution

DPF regeneration duration

Regeneration took longer than allowed or did not finish.

Usual causes
Short trips, faulty exhaust temperature sensor, injector or EGR fault producing extra soot.
In the workshop
Forced regeneration and find why it did not complete. Software solution on request.
P2458: full page →

P2463

Software solution

DPF soot accumulation

The particulate filter is too full.

Usual causes
Short trips, failed regenerations, injector or EGR faults producing extra soot.
In the workshop
Forced regeneration and fix the cause. Software solution available on request.
P2463: full page →

P242F

Software solution

DPF restriction – ash accumulation

The filter is blocked by ash that regeneration cannot burn.

Usual causes
High mileage, oil consumption, wrong engine oil (high ash).
In the workshop
Ash needs cleaning or a new filter. Software solution available on request.
P242F: full page →

P2031

Software solution

Exhaust gas temperature sensor circuit (bank 1, sensor 2)

Electrical fault in an exhaust temperature sensor before or after the DPF.

Usual causes
Failed sensor (heat damage), broken wire, melted connector.
In the workshop
Replace the sensor. DPF regeneration stops without it.
P2031: full page →

P20EE

Software solution

SCR NOx catalyst efficiency below threshold (bank 1)

The AdBlue/SCR system does not reduce NOx enough.

Usual causes
Poor AdBlue quality, faulty dosing module, NOx sensor or SCR catalyst.
In the workshop
Test AdBlue quality and NOx sensors. Software solution available on request.
P20EE: full page →

P20E8

Software solution

Reductant pressure too low

AdBlue pressure in the dosing system is too low.

Usual causes
Failed AdBlue pump, crystallised lines, blocked filter, frozen fluid.
In the workshop
Check the pump and lines. Software solution available on request.
P20E8: full page →

P204F

Software solution

Reductant system performance (bank 1)

The AdBlue system as a whole does not perform as expected.

Usual causes
Dosing module, pump, NOx sensor, wrong or diluted AdBlue.
In the workshop
Full SCR diagnosis. Software solution available on request.
P204F: full page →

P2047

Software solution

Reductant injector circuit / open (bank 1, unit 1)

Electrical fault in the AdBlue injector circuit.

Usual causes
Failed AdBlue injector, wiring damage near the exhaust.
In the workshop
Electrical repair or new injector. Software solution on request.
P2047: full page →

P2BAD

Software solution

NOx exceedence – root cause unknown

NOx emissions are too high and the ECU cannot pinpoint why.

Usual causes
NOx sensor, AdBlue quality, dosing, EGR or SCR catalyst problems.
In the workshop
Work through the SCR system step by step. Software solution available on request.
P2BAD: full page →

P0420

Software solution

Catalyst system efficiency below threshold (bank 1)

The catalytic converter does not clean the exhaust enough.

Usual causes
Worn catalyst, faulty rear lambda sensor, misfires, exhaust leak, or a decat pipe.
In the workshop
Check misfires and lambda sensors first. Software solution available on request.
P0420: full page →

P0430

Software solution

Catalyst system efficiency below threshold (bank 2)

Same as P0420, on the second bank of a V engine.

Usual causes
Worn catalyst, faulty rear lambda sensor, misfires, exhaust leak, or a decat pipe.
In the workshop
Check misfires and lambda sensors first. Software solution available on request.
P0430: full page →

P0604

ECU / write fault

Internal control module RAM error

The ECU found an error in its working memory.

Usual causes
Internal hardware fault, unstable supply voltage.
In the workshop
Bench-read the ECU and compare with the backup. May need repair or replacement.
P0604: full page →

P0605

ECU / write fault

Internal control module ROM error

The ECU found an error in its program memory.

Usual causes
Corrupted flash after a failed write, wrong file for the hardware, internal fault.
In the workshop
Re-write the full original on the bench or in boot mode.
P0605: full page →

P0606

ECU / write fault

Control module processor

The ECU detected an internal processor error.

Usual causes
Hardware fault, water damage, bad write, or wrong software for that hardware.
In the workshop
Read the ECU on the bench and compare with the original backup.
P0606: full page →

P0607

ECU / write fault

Control module performance

The ECU reports that it does not work correctly internally.

Usual causes
Internal fault, supply voltage problems, software mismatch.
In the workshop
Check supply and grounds, then bench-read and compare.
P0607: full page →

P0641

ECU / write fault

Sensor reference voltage "A" circuit / open

The 5 V supply the ECU gives to its sensors is out of range.

Usual causes
A shorted sensor pulling the 5 V line down, wiring damage, ECU fault.
In the workshop
Unplug sensors one by one to find the one that drags the voltage down.
P0641: full page →

P0700

ECU / write fault

Transmission control system (MIL request)

The gearbox ECU (TCU) has stored a fault and asks the engine ECU to light the warning lamp.

Usual causes
Any stored TCU fault: solenoid, sensor, clutch adaptation, oil.
In the workshop
Read the TCU for the real code. Gearbox faults must be fixed before a torque increase.
P0700: full page →

U0100

ECU / write fault

Lost communication with ECM/PCM "A"

Other modules cannot talk to the engine ECU over CAN.

Usual causes
ECU without power, CAN wiring fault, ECU crashed or bricked after a failed write.
In the workshop
Check ECU power and CAN lines. After a failed write, recover the ECU on the bench or in boot mode.
U0100: full page →

U0101

ECU / write fault

Lost communication with TCM

Other modules cannot talk to the gearbox ECU.

Usual causes
TCU power or ground fault, CAN wiring, failed TCU.
In the workshop
Check supply and CAN at the TCU connector.
U0101: full page →

U0401

ECU / write fault

Invalid data received from ECM/PCM "A"

A module receives data from the engine ECU that it cannot accept.

Usual causes
Software mismatch between modules, wrong coding, a file that changed CAN values other modules check.
In the workshop
Check coding and software versions. If it appears after a tune, the file must be corrected.
U0401: full page →