Reference · 33 terms
Chiptuning glossary.
The words used across the database and tech notes, explained the way we use them in the workshop.
- A2L
- Map description file from the ECU supplier (ASAM standard). Gives every map its name, axis and unit. Same role as DAMOS. See DAMOS
- BDM
- Background Debug Mode. A debug port on older Motorola/Freescale processors, used to read and write the ECU directly on the board. See JTAG
- Bench
- Reading or writing an ECU removed from the car, powered on the desk through its connector.
- BIN file
- The raw memory dump of an ECU, byte for byte. Tools read and write BIN; WinOLS keeps it inside an .ols project. See .ols project
- Boot mode
- Starting the ECU processor in its factory programming mode through a test point on the board. Used when OBD and bench are not possible.
- Boost map
- The target turbo pressure by engine speed and load. One of the main maps changed in a Stage 1 file.
- Checksum
- A control value the ECU calculates over its memory. After any change it must be corrected, or the ECU will not start or will set a fault.
- CVN
- Calibration Verification Number. A checksum the ECU reports over OBD so emissions testing can see whether the calibration is original. See Checksum
- DAMOS
- Bosch map description file. With DAMOS, every map in WinOLS has its real name and limits, so nothing is guessed. See A2L
- Datalog
- Recording live engine values (boost, rail pressure, lambda, timing) during a test drive to check a tune.
- DTC
- Diagnostic Trouble Code. A stored fault such as P0299. See the fault code guide.
- Dyno
- A dynamometer that measures power and torque at the wheels or hub. ASF Tuning has 4x4, 2WD hub and bike dynos.
- ECU
- Engine Control Unit. The computer that controls fuel, air, ignition and limits. Every engine page in the database lists its ECU.
- EEPROM
- A small memory chip that stores immobiliser data, VIN and adaptations, separate from the main flash.
- HW number
- Hardware part number of the ECU (for example 03L906018). Printed on the label and used to find the right file. See SW number
- Immo
- Immobiliser. Links the ECU to the key and the car. Immo data lives in EEPROM and must survive every write.
- JTAG
- Standard debug interface on a processor. Used for full reads and for recovering an ECU after a failed write. See BDM
- Mappack
- A set of map definitions for one software version, made by a tuner. Faster than finding maps by hand. See DAMOS
- OBD
- On-Board Diagnostics socket under the dashboard. The quickest way to read and write an ECU without removing it.
- .ols project
- A WinOLS project file: the original read, the modified versions, map definitions and notes in one file. See WinOLS
- Pops & bangs
- A calibration that adds overrun fuel so the exhaust crackles when you lift off. For off-road, motorsport and export use only, where permitted by local law.
- Rail pressure
- Fuel pressure in the common rail of a diesel. Raised carefully in Stage 1; too much sets P0088.
- Slave / Master
- A slave tool is tied to a master tuner, who decodes and modifies its files. The workshop reads and writes; the master makes the file.
- Stage 1
- A software-only tune for a standard car. No hardware changes needed. See Stage 2
- Stage 2
- A tune for a car with upgraded hardware, usually intake, intercooler or exhaust. Needs a Stage 2 file made for those parts. See Stage 1
- Stage X
- Magic Motorsport software for building tuning projects step by step, taught in ASF Academy Intermediate and Advanced. See WinOLS
- SW number
- Software version of the ECU (for example 1037541234 or a 6-digit Bosch number). Two cars with the same HW can have different SW. See HW number
- TCU
- Transmission Control Unit. The gearbox ECU, for example DQ250 or ZF 8HP. See the Gearboxes section of the database.
- Torque limiter
- Maps that cap engine torque by gear, speed or temperature. Raised in a tune together with boost and fuel.
- TPROT
- Tricore protection in newer Bosch EDC17/MED17 software. Blocks OBD reading until the ECU is unlocked on the bench or in boot.
- Tricore
- Infineon processor family used in Bosch EDC17, MED17, MD1 and MG1 ECUs.
- Vmax
- The speed limiter in the ECU. Can be raised or removed in the file.
- WinOLS
- EVC software for editing ECU files and managing projects. The standard tool in professional tuning. See .ols project
A
B
C
D
E
H
I
J
M
O
P
R
S
T
V
W