Guide · how an ECU is read

ECU read methods: OBD, Bench, Boot, JTAG.

Before any file is changed, the original has to be read and saved. This page shows the five routes we use in the workshop and which route fits which ECU family in the database.

The five methods

OBD

Through the diagnostic socket

The ECU stays in the car. The tool talks to the bootloader over CAN or K-line. Fastest route and no opening, but on many newer ECUs it writes only the calibration and cannot read the full flash or EEPROM.

Risk Low, if the battery is on a stable charger.

Bench

ECU out, on the desk

The ECU is removed and powered on the bench; the tool connects to its connector pins. Reads the full flash and EEPROM on most Tricore ECUs without opening the case.

Risk Low to medium. Correct wiring diagram is essential.

Boot

Case opened, boot pin

The case is opened and the processor is forced into boot mode through a test point. Used when bench is not supported or the ECU is locked (TPROT, new SW).

Risk Medium. Needs a steady hand and the right pinout.

JTAG / BDM

Debug port on the board

Direct access to the processor through its debug interface. Classic for older Motorola/Freescale ECUs (EDC16, MED9, Delphi) and for recovery after a failed write.

Risk Medium to high. Soldering or probe frame needed.

EEPROM

Memory chip on the board

The external EEPROM (95xxx, 93Cxx) is read in circuit or desoldered. Holds immobiliser data, VIN and adaptations. Needed for ECU clones and immo work.

Risk Medium. Always keep the original dump.

Which method for which ECU

Typical routes in our workshop. Exact support depends on the software version and on your tool and licence, so always check the tool's vehicle list before you connect.

ECU familyUsual routeFull read / backupECUs in the database
Bosch EDC15 / ME7 (C167)OBD read and writeBoot (BSL) for full read, EEPROM 95xxx for immoÊDC15+ME7.5ME7.1.1
Bosch EDC16 / MED9 (MPC5xx)OBD on most versionsBench or BDM for full read with EEPROMEDC16C31EDC16C34EDC16C39EDC16CP31MED9.1
Bosch EDC17 / MED17 (Tricore, older SW)OBD write of the calibrationBench for full flash + EEPROM backup firstEDC17C46EDC17CP14EDC17C64MED17;5MED17.1
Bosch EDC17 / MED17 with TPROT (newer SW)Bench or BootOBD often limited until the ECU is unlockedEDC17C74EDC17CP44MED17.5.5
Bosch MD1 / MG1Bench with unlock procedureOBD only after unlock, on supported toolsMD1CP004MD1CS001MG1CS003
Continental SID / PCR / SIMOSOBD on many versionsBench or Boot for full readPCR2.1SID208SID807SIMOS18
Delphi CRD / DCMOBD or BenchJTAG/BDM for recoveryCRD3CRD2
Gearboxes (TCU)OBD on supported versionsBench; never interrupt a TCU writeDQ250DQ200ZGS001
Magic FlexOBD, Bench and Boot in one tool. Strong on MD1/MG1 unlock and Tricore bench.OBD · Bench · Boot
Alientech KESS3Widely used master/slave tool for OBD, Bench and Boot on cars, trucks and bikes.OBD · Bench · Boot
AutotunerFast OBD and Bench with clear wiring guides. Good for workshops starting out.OBD · Bench · Boot
DimsportNew Genius (OBD) and Trasdata (Bench/Boot/BDM), common on older and agricultural ECUs.OBD · Bench · BDM
EEPROM programmerFor 95xxx / 93Cxx chips: immo data, VIN, clones, recovery.EEPROM

Five rules before every read

01Battery on a stable charger, 13.5–14 V, for the whole read and write.
02Save the full original (flash + EEPROM) in two places before anything else.
03Write down HW and SW numbers from the label and from the read. They must match.
04Check fault codes before tuning. A car with P0299 needs repair, not a remap.
05After writing: clear codes, check live data, test drive.